aws_directconnect_virtual_interface

account_id

Type: STRING

address_family

Type: STRING
Provider name: addressFamily
Description: The address family for the BGP peer.

amazon_address

Type: STRING
Provider name: amazonAddress
Description: The IP address assigned to the Amazon interface.

amazon_side_asn

Type: INT64
Provider name: amazonSideAsn
Description: The autonomous system number (ASN) for the Amazon side of the connection.

asn

Type: INT32
Provider name: asn
Description: The autonomous system (AS) number for Border Gateway Protocol (BGP) configuration. The valid values are 1-2147483647.

auth_key

Type: STRING
Provider name: authKey
Description: The authentication key for BGP configuration. This string has a minimum length of 6 characters and and a maximun lenth of 80 characters.

aws_device_v2

Type: STRING
Provider name: awsDeviceV2
Description: The Direct Connect endpoint that terminates the physical connection.

aws_logical_device_id

Type: STRING
Provider name: awsLogicalDeviceId
Description: The Direct Connect endpoint that terminates the logical connection. This device might be different than the device that terminates the physical connection.

bgp_peers

Type: UNORDERED_LIST_STRUCT
Provider name: bgpPeers
Description: The BGP peers configured on this virtual interface.

• address_family
  Type: STRING
  Provider name: addressFamily
  Description: The address family for the BGP peer.
  
• amazon_address
  Type: STRING
  Provider name: amazonAddress
  Description: The IP address assigned to the Amazon interface.
  
• asn
  Type: INT32
  Provider name: asn
  Description: The autonomous system (AS) number for Border Gateway Protocol (BGP) configuration.
  
• auth_key
  Type: STRING
  Provider name: authKey
  Description: The authentication key for BGP configuration. This string has a minimum length of 6 characters and and a maximun lenth of 80 characters.
  
• aws_device_v2
  Type: STRING
  Provider name: awsDeviceV2
  Description: The Direct Connect endpoint that terminates the BGP peer.
  
• aws_logical_device_id
  Type: STRING
  Provider name: awsLogicalDeviceId
  Description: The Direct Connect endpoint that terminates the logical connection. This device might be different than the device that terminates the physical connection.
  
• bgp_peer_id
  Type: STRING
  Provider name: bgpPeerId
  Description: The ID of the BGP peer.
  
• bgp_peer_state
  Type: STRING
  Provider name: bgpPeerState
  Description: The state of the BGP peer. The following are the possible values:
  • verifying: The BGP peering addresses or ASN require validation before the BGP peer can be created. This state applies only to public virtual interfaces.
  • pending: The BGP peer is created, and remains in this state until it is ready to be established.
  • available: The BGP peer is ready to be established.
  • deleting: The BGP peer is being deleted.
  • deleted: The BGP peer is deleted and cannot be established.
• bgp_status
  Type: STRING
  Provider name: bgpStatus
  Description: The status of the BGP peer. The following are the possible values:
  • up: The BGP peer is established. This state does not indicate the state of the routing function. Ensure that you are receiving routes over the BGP session.
  • down: The BGP peer is down.
  • unknown: The BGP peer status is not available.
• customer_address
  Type: STRING
  Provider name: customerAddress
  Description: The IP address assigned to the customer interface.
  

connection_id

Type: STRING
Provider name: connectionId
Description: The ID of the connection.

customer_address

Type: STRING
Provider name: customerAddress
Description: The IP address assigned to the customer interface.

customer_router_config

Type: STRING
Provider name: customerRouterConfig
Description: The customer router configuration.

direct_connect_gateway_id

Type: STRING
Provider name: directConnectGatewayId
Description: The ID of the Direct Connect gateway.

jumbo_frame_capable

Type: BOOLEAN
Provider name: jumboFrameCapable
Description: Indicates whether jumbo frames are supported.

location

Type: STRING
Provider name: location
Description: The location of the connection.

mtu

Type: INT32
Provider name: mtu
Description: The maximum transmission unit (MTU), in bytes. The supported values are 1500 and 8500. The default value is 1500

owner_account

Type: STRING
Provider name: ownerAccount
Description: The ID of the Amazon Web Services account that owns the virtual interface.

region

Type: STRING
Provider name: region
Description: The Amazon Web Services Region where the virtual interface is located.

route_filter_prefixes

Type: UNORDERED_LIST_STRUCT
Provider name: routeFilterPrefixes
Description: The routes to be advertised to the Amazon Web Services network in this Region. Applies to public virtual interfaces.

• cidr
  Type: STRING
  Provider name: cidr
  Description: The CIDR block for the advertised route. Separate multiple routes using commas. An IPv6 CIDR must use /64 or shorter.
  

site_link_enabled

Type: BOOLEAN
Provider name: siteLinkEnabled
Description: Indicates whether SiteLink is enabled.

tags

Type: UNORDERED_LIST_STRING

virtual_gateway_id

Type: STRING
Provider name: virtualGatewayId
Description: The ID of the virtual private gateway. Applies only to private virtual interfaces.

virtual_interface_arn

Type: STRING

virtual_interface_id

Type: STRING
Provider name: virtualInterfaceId
Description: The ID of the virtual interface.

virtual_interface_name

Type: STRING
Provider name: virtualInterfaceName
Description: The name of the virtual interface assigned by the customer network. The name has a maximum of 100 characters. The following are valid characters: a-z, 0-9 and a hyphen (-).

virtual_interface_state

Type: STRING
Provider name: virtualInterfaceState
Description: The state of the virtual interface. The following are the possible values:

• confirming: The creation of the virtual interface is pending confirmation from the virtual interface owner. If the owner of the virtual interface is different from the owner of the connection on which it is provisioned, then the virtual interface will remain in this state until it is confirmed by the virtual interface owner.
• verifying: This state only applies to public virtual interfaces. Each public virtual interface needs validation before the virtual interface can be created.
• pending: A virtual interface is in this state from the time that it is created until the virtual interface is ready to forward traffic.
• available: A virtual interface that is able to forward traffic.
• down: A virtual interface that is BGP down.
• deleting: A virtual interface is in this state immediately after calling DeleteVirtualInterface until it can no longer forward traffic.
• deleted: A virtual interface that cannot forward traffic.
• rejected: The virtual interface owner has declined creation of the virtual interface. If a virtual interface in the Confirming state is deleted by the virtual interface owner, the virtual interface enters the Rejected state.
• unknown: The state of the virtual interface is not available.

virtual_interface_type

Type: STRING
Provider name: virtualInterfaceType
Description: The type of virtual interface. The possible values are private and public.

vlan

Type: INT32
Provider name: vlan
Description: The ID of the VLAN.