Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces
Description
To set the runtime status of the net.ipv4.conf.default.accept_redirects kernel parameter, run the following command:
$ sudo sysctl -w net.ipv4.conf.default.accept_redirects=0
To make sure that the setting is persistent, add the following line to a file in the directory /etc/sysctl.d:
net.ipv4.conf.default.accept_redirects = 0
Rationale
ICMP redirect messages are used by routers to inform hosts that a more
direct route exists for a particular destination. These messages modify the
host’s route table and are unauthenticated. An illicit ICMP redirect
message could result in a man-in-the-middle attack.
This feature of the IPv4 protocol has few legitimate uses. It should
be disabled unless absolutely required.
Shell script
The following script can be run on the host to remediate the issue.
#!/bin/bash
# Remediation is applicable only in certain platforms
if dpkg-query --show --showformat='${db:Status-Status}' 'linux-base' 2>/dev/null | grep -q '^installed$'; then
#
# Set sysctl config file which to save the desired value
#
SYSCONFIG_FILE="/etc/sysctl.conf"
# Comment out any occurrences of net.ipv4.conf.default.accept_redirects from /etc/sysctl.d/*.conf files
for f in /etc/sysctl.d/*.conf /run/sysctl.d/*.conf /usr/local/lib/sysctl.d/*.conf /etc/ufw/sysctl.conf; do
# skip systemd-sysctl symlink (/etc/sysctl.d/99-sysctl.conf -> /etc/sysctl.conf)
if [[ "$(readlink -f "$f")" == "/etc/sysctl.conf" ]]; then continue; fi
if [[ "$(readlink -f "$f")" == "$(readlink -f "${SYSCONFIG_FILE}")" ]]; then
# entries starting with net.ipv4.conf.default.accept_redirects in the file this remediation writes to
# are replaced in place below, commenting them out would make the remediation non-idempotent
matching_list=$(grep -P '^(?!#)(?!net.ipv4.conf.default.accept_redirects\b).*[\s]*net.ipv4.conf.default.accept_redirects.*$' $f | uniq )
else
matching_list=$(grep -P '^(?!#).*[\s]*net.ipv4.conf.default.accept_redirects.*$' $f | uniq )
fi
if ! test -z "$matching_list"; then
while IFS= read -r entry; do
escaped_entry=$(sed -e 's|/|\\/|g' <<< "$entry")
# comment out "net.ipv4.conf.default.accept_redirects" matches to preserve user data
sed -i --follow-symlinks "s/^${escaped_entry}$/# &/g" $f
done <<< "$matching_list"
fi
done
sysctl_net_ipv4_conf_default_accept_redirects_value='0'
#
# Set runtime for net.ipv4.conf.default.accept_redirects
#
if ! /bin/false ; then
/sbin/sysctl -q -n -w net.ipv4.conf.default.accept_redirects="$sysctl_net_ipv4_conf_default_accept_redirects_value"
fi
#
# If net.ipv4.conf.default.accept_redirects present in /etc/sysctl.conf, change value to appropriate value
# else, add "net.ipv4.conf.default.accept_redirects = value" to /etc/sysctl.conf
#
# Strip any search characters in the key arg so that the key can be replaced without
# adding any search characters to the config file.
stripped_key=$(sed 's/[\^=\$,;+]*//g' <<< "^net.ipv4.conf.default.accept_redirects")
# shellcheck disable=SC2059
printf -v formatted_output "%s = %s" "$stripped_key" "$sysctl_net_ipv4_conf_default_accept_redirects_value"
# If the key exists, change it. Otherwise, add it to the config_file.
# We search for the key string followed by a word boundary (matched by \>),
# so if we search for 'setting', 'setting2' won't match.
if LC_ALL=C grep -q -m 1 -i -e "^net.ipv4.conf.default.accept_redirects\\>" "${SYSCONFIG_FILE}"; then
escaped_formatted_output=$(sed -e 's|/|\\/|g' <<< "$formatted_output")
LC_ALL=C sed -i --follow-symlinks "s/^net.ipv4.conf.default.accept_redirects\\>.*/$escaped_formatted_output/gi" "${SYSCONFIG_FILE}"
else
if [[ -s "${SYSCONFIG_FILE}" ]] && [[ -n "$(tail -c 1 -- "${SYSCONFIG_FILE}" || true)" ]]; then
LC_ALL=C sed -i --follow-symlinks '$a'\\ "${SYSCONFIG_FILE}"
fi
printf '%s\n' "$formatted_output" >> "${SYSCONFIG_FILE}"
fi
else
>&2 echo 'Remediation is not applicable, nothing was done'
fi
Ansible playbook
The following playbook can be run with Ansible to remediate the issue.
- name: Gather the package facts
package_facts:
manager: auto
tags:
- CJIS-5.10.1.1
- NIST-800-53-CM-6(a)
- NIST-800-53-CM-7(a)
- NIST-800-53-CM-7(b)
- NIST-800-53-SC-7(a)
- PCI-DSS-Req-1.4.3
- PCI-DSSv4-1.4
- PCI-DSSv4-1.4.3
- disable_strategy
- low_complexity
- medium_disruption
- medium_severity
- reboot_required
- sysctl_net_ipv4_conf_default_accept_redirects
- name: XCCDF Value sysctl_net_ipv4_conf_default_accept_redirects_value # promote to variable
set_fact:
sysctl_net_ipv4_conf_default_accept_redirects_value: !!str 0
tags:
- always
- name: Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces
- Set fact for sysctl paths
ansible.builtin.set_fact:
sysctl_paths:
- /etc/sysctl.d/
- /run/sysctl.d/
- /usr/local/lib/sysctl.d/
when: '"linux-base" in ansible_facts.packages'
tags:
- CJIS-5.10.1.1
- NIST-800-53-CM-6(a)
- NIST-800-53-CM-7(a)
- NIST-800-53-CM-7(b)
- NIST-800-53-SC-7(a)
- PCI-DSS-Req-1.4.3
- PCI-DSSv4-1.4
- PCI-DSSv4-1.4.3
- disable_strategy
- low_complexity
- medium_disruption
- medium_severity
- reboot_required
- sysctl_net_ipv4_conf_default_accept_redirects
- name: Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces
- Find all files that contain net.ipv4.conf.default.accept_redirects
ansible.builtin.shell:
cmd: |-
set -o pipefail
find -L {{ sysctl_paths | join(" ") }} -type f -name '*.conf' | xargs grep -HP '^\s*net.ipv4.conf.default.accept_redirects\s*=\s*.*$'
executable: /bin/bash
register: find_all_values
check_mode: false
changed_when: false
failed_when: false
when: '"linux-base" in ansible_facts.packages'
tags:
- CJIS-5.10.1.1
- NIST-800-53-CM-6(a)
- NIST-800-53-CM-7(a)
- NIST-800-53-CM-7(b)
- NIST-800-53-SC-7(a)
- PCI-DSS-Req-1.4.3
- PCI-DSSv4-1.4
- PCI-DSSv4-1.4.3
- disable_strategy
- low_complexity
- medium_disruption
- medium_severity
- reboot_required
- sysctl_net_ipv4_conf_default_accept_redirects
- name: Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces
- Find all files that set net.ipv4.conf.default.accept_redirects to correct value
ansible.builtin.shell:
cmd: |-
set -o pipefail
find -L {{ sysctl_paths | join(" ") }} -type f -name '*.conf' | xargs grep -HP '^\s*net.ipv4.conf.default.accept_redirects\s*=\s*{{ sysctl_net_ipv4_conf_default_accept_redirects_value }}$'
executable: /bin/bash
register: find_correct_value
check_mode: false
changed_when: false
failed_when: false
when: '"linux-base" in ansible_facts.packages'
tags:
- CJIS-5.10.1.1
- NIST-800-53-CM-6(a)
- NIST-800-53-CM-7(a)
- NIST-800-53-CM-7(b)
- NIST-800-53-SC-7(a)
- PCI-DSS-Req-1.4.3
- PCI-DSSv4-1.4
- PCI-DSSv4-1.4.3
- disable_strategy
- low_complexity
- medium_disruption
- medium_severity
- reboot_required
- sysctl_net_ipv4_conf_default_accept_redirects
- name: Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces
- Comment out any occurrences of net.ipv4.conf.default.accept_redirects from config
files
ansible.builtin.replace:
path: '{{ item | split(":") | first }}'
regexp: ^[\s]*net.ipv4.conf.default.accept_redirects
replace: '#net.ipv4.conf.default.accept_redirects'
loop: '{{ find_all_values.stdout_lines }}'
when:
- '"linux-base" in ansible_facts.packages'
- find_correct_value.stdout_lines | length == 0 or find_all_values.stdout_lines
| length > find_correct_value.stdout_lines | length
tags:
- CJIS-5.10.1.1
- NIST-800-53-CM-6(a)
- NIST-800-53-CM-7(a)
- NIST-800-53-CM-7(b)
- NIST-800-53-SC-7(a)
- PCI-DSS-Req-1.4.3
- PCI-DSSv4-1.4
- PCI-DSSv4-1.4.3
- disable_strategy
- low_complexity
- medium_disruption
- medium_severity
- reboot_required
- sysctl_net_ipv4_conf_default_accept_redirects
- name: Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces
- Comment out any occurrences of net.ipv4.conf.default.accept_redirects from /etc/ufw/sysctl.conf
ansible.builtin.replace:
path: /etc/ufw/sysctl.conf
regexp: (^[\s]*net.ipv4.conf.default.accept_redirects.*$)
replace: '# \1'
when: '"linux-base" in ansible_facts.packages'
tags:
- CJIS-5.10.1.1
- NIST-800-53-CM-6(a)
- NIST-800-53-CM-7(a)
- NIST-800-53-CM-7(b)
- NIST-800-53-SC-7(a)
- PCI-DSS-Req-1.4.3
- PCI-DSSv4-1.4
- PCI-DSSv4-1.4.3
- disable_strategy
- low_complexity
- medium_disruption
- medium_severity
- reboot_required
- sysctl_net_ipv4_conf_default_accept_redirects
- name: Disable Kernel Parameter for Accepting ICMP Redirects by Default on IPv4 Interfaces
- Ensure sysctl net.ipv4.conf.default.accept_redirects is set
ansible.posix.sysctl:
name: net.ipv4.conf.default.accept_redirects
value: '{{ sysctl_net_ipv4_conf_default_accept_redirects_value }}'
sysctl_file: /etc/sysctl.conf
state: present
reload: true
when: '"linux-base" in ansible_facts.packages'
tags:
- CJIS-5.10.1.1
- NIST-800-53-CM-6(a)
- NIST-800-53-CM-7(a)
- NIST-800-53-CM-7(b)
- NIST-800-53-SC-7(a)
- PCI-DSS-Req-1.4.3
- PCI-DSSv4-1.4
- PCI-DSSv4-1.4.3
- disable_strategy
- low_complexity
- medium_disruption
- medium_severity
- reboot_required
- sysctl_net_ipv4_conf_default_accept_redirects